China OEM 110 Screw Elements and Shafts wheel and axle

Product Description

110 twin screw extruder screw elements and shaft

Technical Specification

Screw Type 110  
Screw Diameter  
Vacuum Quenching By Ourself
Supplier Screw Design Yes
Hardness 58-62HRC
Suface Treatment Polishing Sand Blasting
Warranty 1 Years
Range 15.6-400mm
Heat Treatment By Ourself
Screw Element Precision Higher than HangZhou Factory  
Materials SKD11 WR5 WR45 WR14 Stainless Steel HIP Nickel Alloy 38CrMoAla 316L ……
Application Industries Chemical  /Food  /Phamaceuticals /Powder Coating/ Midical

Co-rotating twin screw elements for 
-APV             -KOBE                         -OMC
-Buhler          -Theysohn
-Buss             -Toshiba
-Clextral        -Labtech                       -USEON
-Coperio      -Lantai                         – others
-JSW            -Leistritz    
-Keya            -Maris

Types of the Screw Segments
* Convey Screw Segment              * Mixing Screw Segment
* Kneading Block & Disk                * Transition Screw Element
* Deep groove transfer element     * Screw element for side feeder
* 1-flighted,2-flighted,3-flighted screw elements

Screw Element Materials:
For wear application:
* Tool Steel : W6Mo5Cr4V2;
* PM-HIP material : SAM10,SAM26,SAM39,CPM10V,CPM9V
For corrision application:
* Nitrided Steel: 38CrMoAI;
* PM-HIP material : SAM26,SAM39,CPM10V,CPM9V
For wear and corrision application:
* PM-HIP material:SAM26,SAM39,CPM10V,CPM9V
Other materials:
Stainless Steel: 316L,C276 etc.
By working closely with customers in choosing optional materials,we can minimize wear and tear and associated costs.

Quality Control
1.Materials Control: 
All the materials are purchased from the domestic brands of Eurpean twin screw specialty materials suppilers, which tested by elemental analysis and metallurgical inspections to ensure the quality.
2.The internal splines is checked by the spline plug to ensure interchangeability of the elemets
3.All components are machined by CNC machines to ensure the shapes and tolerances of the elements.
4.Adopt the European high speed steel powder processing technology, and to the heat treatment according to the strict heat treatment process to ensure the wear and corrosion performance same as the foreigh brands.
5.Professioal technical team can not only provide timely and accurate mapping sample design but also the combination of elements of technical services
6.There are various prepared technical information and fitxtures for the various brands extruders to ensure the timely lead time. The common components have a lot of stock,even the new one, it can be delivered within 45days.
7.The modern management system can ensure the product 100% qualified and tracked.

Our strengths are based on many years experience supplying the following:
* Competitive costs per unit of production 
* Fast turn round for collection and delivery on refurbished parts 
* Parts available from stock for a wide range of extruder makes 
* Comprehensive inspection procedure on all parts prior to dispatch 
* A time proven quality service 
* Latest manufacturing techniques and metallurgy, ensuring consistent and reliable performance of parts 
* Customized solutions to meet specific needs.

Heat Treatment by Ourself
As we all know,heat treatment is very important in the screw production process,In order to ensure the quality of products ,Joiner has purchased professional heat treatment equipment to produce, so that we can control the construction process by ourselves. In China,We are the only company that does the heat treatment by ourselves and the heat treatment of screw elements made by HangZhou factory is processed by outsiders, so the quality of products can not only be completely guarantee.

Production and Inspection Equipment

Packing and Delivery
Packing Details: Standard packing for CHINAMFG Extruder twin screw extruder parts
Delivery Time: Shipped in 30 Days after payment for extruder screw and barrel
To product antirust processing and then use the paper package, bubble,fixed in the wooden case , after confirm the delivery.

FRQ
 
1. Q: Are you a factory or trading company? 
 —-A: A factory
2. Q: Where is your factory located? How can I visit there? 
—–A: Our factory is located in HangZhou, ZheJiang  Province, China, 
1) You can fly to HangZhou Airport directly. We will pick you up when you arrive in the airport; 
All our clients, from domestic or abroad, are warmly welcome to visit us! 
                                             
3.Q: What makes you different with others?
—-A: 1) Our Excellent Service 
 For a quick, no hassle quote just send email to us
 We promise to reply with a price within 24 hours – sometimes even within the hour.
 If you need an advice, just call our export office at   571 87226313, we will answer your questions immediately.
2) Our quick manufacturing time
For Normal orders, we will promise to produce within 30 working days.
As a manufacturer, we can ensure the delivery time according to the formal contract.
 
 4.Q: How about the delivery time? 
—-A: This depends on the product. Typically standard products are delivered within 30 days. 
 

  1.  Q: What is the term of payment? 
    —-A: 1) T/T payment;   2) LC;  

 
6.Q: May I know the status of my order?
—-A: Yes .We will send you information and photos at different production stage of your order. You will get the latest information in time. 

 

 

After-sales Service: 1 Year
Warranty: 1 Year
Standard: DIN, ISO9001
Technics: CNC Process
Feature: Recycle
Material: Metal
Customization:
Available

|

Customized Request

screwshaft

Screw Sizes and Their Uses

Screws have different sizes and features. This article will discuss screw sizes and their uses. There are two main types: right-handed and left-handed screw shafts. Each screw features a point that drills into the object. Flat tipped screws, on the other hand, need a pre-drilled hole. These screw sizes are determined by the major and minor diameters. To determine which size of screw you need, measure the diameter of the hole and the screw bolt’s thread depth.

The major diameter of a screw shaft

The major diameter of a screw shaft is the distance from the outer edge of the thread on one side to the tip of the other. The minor diameter is the inner smooth part of the screw shaft. The major diameter of a screw is typically between two and sixteen inches. A screw with a pointy tip has a smaller major diameter than one without. In addition, a screw with a larger major diameter will have a wider head and drive.
The thread of a screw is usually characterized by its pitch and angle of engagement. The pitch is the angle formed by the helix of a thread, while the crest forms the surface of the thread corresponding to the major diameter of the screw. The pitch angle is the angle between the gear axis and the pitch surface. Screws without self-locking threads have multiple starts, or helical threads.
The pitch is a crucial component of a screw’s threading system. Pitch is the distance from a given thread point to the corresponding point of the next thread on the same shaft. The pitch line is one element of pitch diameter. The pitch line, or lead, is a crucial dimension for the thread of a screw, as it controls the amount of thread that will advance during a single turn.

The pitch diameter of a screw shaft

When choosing the appropriate screw, it is important to know its pitch diameter and pitch line. The pitch line designates the distance between adjacent thread sides. The pitch diameter is also known as the mean area of the screw shaft. Both of these dimensions are important when choosing the correct screw. A screw with a pitch of 1/8 will have a mechanical advantage of 6.3. For more information, consult an application engineer at Roton.
The pitch diameter of a screw shaft is measured as the distance between the crest and the root of the thread. Threads that are too long or too short will not fit together in an assembly. To measure pitch, use a measuring tool with a metric scale. If the pitch is too small, it will cause the screw to loosen or get stuck. Increasing the pitch will prevent this problem. As a result, screw diameter is critical.
The pitch diameter of a screw shaft is measured from the crest of one thread to the corresponding point on the next thread. Measurement is made from one thread to another, which is then measured using the pitch. Alternatively, the pitch diameter can be approximated by averaging the major and minor diameters. In most cases, the pitch diameter of a screw shaft is equal to the difference between the two.

The thread depth of a screw shaft

Often referred to as the major diameter, the thread depth is the outermost diameter of the screw. To measure the thread depth of a screw, use a steel rule, micrometer, or caliper. In general, the first number in the thread designation indicates the major diameter of the thread. If a section of the screw is worn, the thread depth will be smaller, and vice versa. Therefore, it is good practice to measure the section of the screw that receives the least amount of use.
In screw manufacturing, the thread depth is measured from the crest of the screw to the root. The pitch diameter is halfway between the major and minor diameters. The lead diameter represents the amount of linear distance traveled in one revolution. As the lead increases, the load capacity decreases. This measurement is primarily used in the construction of screws. However, it should not be used for precision machines. The thread depth of a screw shaft is essential for achieving accurate screw installation.
To measure the thread depth of a screw shaft, the manufacturer must first determine how much material the thread is exposed to. If the thread is exposed to side loads, it can cause the nut to wedge. Because the nut will be side loaded, its thread flanks will contact the nut. The less clearance between the nut and the screw, the lower the clearance between the nut and the screw. However, if the thread is centralized, there is no risk of the nut wedgeing.
screwshaft

The lead of a screw shaft

Pitch and lead are two measurements of a screw’s linear distance per turn. They’re often used interchangeably, but their definitions are not the same. The difference between them lies in the axial distance between adjacent threads. For single-start screws, the pitch is equal to the lead, while the lead of a multi-start screw is greater than the pitch. This difference is often referred to as backlash.
There are two ways to calculate the pitch and lead of a screw. For single-start screws, the lead and pitch are equal. Multiple-start screws, on the other hand, have multiple starts. The pitch of a multiple-start screw is the same as its lead, but with two or more threads running the length of the screw shaft. A square-thread screw is a better choice in applications requiring high load-bearing capacity and minimal friction losses.
The PV curve defines the safe operating limits of lead screw assemblies. It describes the inverse relationship between contact surface pressure and sliding velocity. As the load increases, the lead screw assembly must slow down in order to prevent irreversible damage from frictional heat. Furthermore, a lead screw assembly with a polymer nut must reduce rpm as the load increases. The more speed, the lower the load capacity. But, the PV factor must be below the maximum allowed value of the material used to make the screw shaft.

The thread angle of a screw shaft

The angle between the axes of a thread and the helix of a thread is called the thread angle. A unified thread has a 60-degree angle in all directions. Screws can have either a tapped hole or a captive screw. The screw pitch is measured in millimeters (mm) and is usually equal to the screw major diameter. In most cases, the thread angle will be equal to 60-degrees.
Screws with different angles have various degrees of thread. Originally, this was a problem because of the inconsistency in the threading. However, Sellers’s thread was easier to manufacture and was soon adopted as a standard throughout the United States. The United States government began to adopt this thread standard in the mid-1800s, and several influential corporations in the railroad industry endorsed it. The resulting standard is called the United States Standard thread, and it became part of the ASA’s Vol. 1 publication.
There are two types of screw threads: coarse and fine. The latter is easier to tighten and achieves tension at lower torques. On the other hand, the coarse thread is deeper than the fine one, making it easier to apply torque to the screw. The thread angle of a screw shaft will vary from bolt to bolt, but they will both fit in the same screw. This makes it easier to select the correct screw.
screwshaft

The tapped hole (or nut) into which the screw fits

A screw can be re-threaded without having to replace it altogether. The process is different than that of a standard bolt, because it requires threading and tapping. The size of a screw is typically specified by its major and minor diameters, which is the inside distance between threads. The thread pitch, which is the distance between each thread, is also specified. Thread pitch is often expressed in threads per inch.
Screws and bolts have different thread pitches. A coarse thread has fewer threads per inch and a longer distance between threads. It is therefore larger in diameter and longer than the material it is screwed into. A coarse thread is often designated with an “A” or “B” letter. The latter is generally used in smaller-scale metalworking applications. The class of threading is called a “threaded hole” and is designated by a letter.
A tapped hole is often a complication. There is a wide range of variations between the sizes of threaded holes and nut threads, so the tapped hole is a critical dimension in many applications. However, even if you choose a threaded screw that meets the requisite tolerance, there may be a mismatch in the thread pitch. This can prevent the screw from freely rotating.

China OEM 110 Screw Elements and Shafts   wheel and axleChina OEM 110 Screw Elements and Shafts   wheel and axle
editor by CX 2023-11-03

Leave a Reply

Your email address will not be published. Required fields are marked *